Quadro SW-Version 4.1.x Instalační příručka stáhnout pdf (Strana 93)

QuadroISDN Manual II: Administrator's Guide Extension User’s Menus

QuadroISDN; SW Version 4.1.x 93

When clicking on the Address in the Caller ID Based

Services table, the caller ID based services configuration

pages for the corresponding extension will be displayed.

The Caller ID Based Services for Address page

consists of two frames. In the left frame all caller ID

based services are listed. Clicking on the corresponding

caller ID based service, its settings will be displayed in

the right frame.

Please Note: Remember to save changes before moving

between the caller ID based services configuration

pages.

Fig. 3-20 Caller ID Based Services for Address page

Below are the instructions to configure each caller ID based service available to the user.

To Configure Caller ID Based Services

1. Press the Add button on the Caller ID Based Services page. The Caller ID Based Services - Add Entry page, where new addresses can be

defined, will appear in the browser window.

2. Define an optional Description of the address.

3. Select the call type from the Call Type drop down list.

4. Enter the SIP address, extension or PSTN number (dependant on the chosen call type) in the Address text field according to the entering rules.

5. To add an address to the Caller ID Based Services table, click Save.

6. Click on the newly created Address in the Caller ID Based Services table to open the Caller ID Based Services for Address page.

7. From the left frame, choose a Caller ID Based Services. From the right frame, enable, configure and adjust the corresponding service. Do this

for each service. Remember to Save the configurations each time moving between the Caller ID Based Services configuration pages.

To Edit Caller ID Based Services

1. Select the checkbox of the corresponding address that has to be edited in the Caller ID Based Services table. The Caller ID Based Services -

Edit Entry page will appear in the browser window.

2. Change the Description of the address, if needed.

3. Change the Call Type and the Address defined in the corresponding fields.

4. Save changes.

5. If the reconfiguration of Caller ID Based Services is needed, click on the corresponding Address in the Caller ID Based Services table to

open the Caller ID Based Services for Address page.

6. From the left frame, choose a Caller ID Based Services. From the right frame, change the corresponding service settings, if required.

Remember to Save the configurations each time moving between the Caller ID Based Services configuration pages.

Incoming Call Blocking

Incoming Call Blocking allows blocking unwanted incoming calls for a Quadro extension. This page provides the necessary settings for incoming

call blocking. It indicates if the service is enabled for the particular caller and whether or not the custom message will be used to inform the caller

about the call being blocked. If the service for the particular caller has been enabled by the administrator and has been stated as protected, the user

cannot disable it.

Please Note: The administrator can protect the service from being disabled by you. Contact the administrator if callers complain that they cannot

reach you.

The Enable Service checkbox selection blocks all calls to the current extension using the corresponding Address listed in the Caller ID Based

Services table where the Incoming Call Blocking service is configured.

The Send Message to Caller Party checkbox is available when the service is enabled and initiates a message to inform the caller that their line has

been blocked. Otherwise, the calling party will be disconnected without notification.

The Restore Default Blocking Call File restores the default incoming call blocking message if another user-defined file has been previously

selected. When the checkbox is selected, the file upload possibility will be disabled.

The Upload New Blocking Call File requires the name of

the desired voice message file. The file needs to be in

PCMU wave format, otherwise the system will prevent

uploading it and the “Invalid audio file, or format is not

supported” warning message will be received. The system

also prevents uploading if there is not enough space

available for the corresponding extension. You will then

receive the “You do not have enough space” warning.

Browse is used to browse custom voice message used for

incoming call blocking.

The Download Voice Message File link only appears if a

file has been previously uploaded. The link is used to

download the audio file to the PC and opens a window

where the saving location can be specified.

Fig. 3-21 Incoming Call Blocking page

1 2 ... 88 89 90 91 92 93 94 95 96 97 98 ... 105 106

Komentáře k této Příručce

Žádné komentáře

Quadro SW-Version 4.1.x Instalační příručka Strana 93

Komentáře k této Příručce

Související produkty a manuály pro Systémy pobočkových ústředen (PBX) Quadro SW-Version 4.1.x